1. R.Nasiri-Zarandi , Ag. Ghaheri, K.Abbaszadeh, "Thermal Modeling and Analysis of a Novel Transverse Flux HAPM Generator for Small Scale Wind Turbine Application" To be Accepeted in IEEE Transactions on Energy Conversion, Article in press 2019
2. A.Mohammadi Ajamloo; K.Abbaszadeh; R. Nasiri-Zarand, "A Novel Transverse Flux Permanent Magnet Generator for Small-Scale Direct Drive Wind Turbine Application: Design and Analysis", International Journal of science and technology (Scientia Iranica) Articles in Press, Accepted Manuscript , Available Online from 22 July 2019
3. S Hajiaghasi, K.Abbaszadeh, A Salemnia, "A New Approach for Transformer Interturn Faults Detection Using Vibration Frequency Analysis" Iranian. J. Electr. Electron. Eng 15 (1), 14-28, 2019
4. M. Jafari, K.Abbaszadeh, "A novel DTC-SVM approach for two parallel-connected induction motors fed by matrix converter" Turkish Journal of Electrical Engineering and Computer Sciences, 2018,
5. K.Abbaszadeh, S.Ebrahimi, "Modelling, Simulation & Blade Pitch Fault Detection of Wind Turbines Equipped with permanent Magnet Synchronous Generator Based-on Support Vector Machine" Vol 10, N01, Spring 2016, Journal of Control, Iran
6. Peyman Saadat, K.Abbaszadeh, "A Single Switch High Step up DC-DC Converter Based on Quadratic Boost", To be accepted in IEEE Tran. On Industrial Electronic.
7. Ahmad Reza Naderi, K.Abbaszadeh," A Novel High Step-up DC-DC Converter with Input Current Ripple Cancelation", To be accepted in IET Power Electronics.
8. Ajily, Ehsan. Ardebili, Mohammad; K.Abbaszadeh,"Magnet Defect and Rotor Eccentricity Modeling in Axial Flux Permanent Magnet Machines via 3D Field Reconstruction Method Conformal Mapping Method", To be Accepeted in IEEE Transactions on Energy Conversion
9. K.Abbaszadeh, F. Saffar,"Modelling & Analyses of electromagnetic forces in distribution transformer under healthy and faulty condition",to be accepted in Journal of IAEEE.
10. K.Abbaszadeh and Farhad Rezaee Alam, "On-Load Field Component Separation in Surface Mounted Permanent Magnet Motors using an Improved Conformal Mapping Method", IEEE Transactions on Magnetics, (Volume:PP , Issue: 99 ), 2015
11. Farhad Rezaee Alam and K.Abbaszadeh,"Magnetic Field Analysis in Eccentric Surface-Mounted Permanent-Magnet Motors Using an Improved Conformal Mapping Method", IEEE Transactions on Energy Conversion, (Volume:PP , Issue: 99 ) Digital Object Identifier 10.1109/TEC.2015.2479562, 2015
12. K.Abbaszadeh, A. Rahimi ,"Analytical Quasi 3D Modeling of an Axial Flux PM Motor with Static Eccentricity Fault ",International Journal of Science and Technology (Scientica iranica) Sharif Univ, 2015
13. Mohammad Khalilzadeh, K.Abbaszadeh,"Non-isolated high step-up DC-DC converter based on coupled inductor with reduced voltage stress", IET Power Electronics, Volume 8, Issue 11, November 2015, p. 2184 - 2194 doi: 10.1049/iet-pel.2014.0899, 2014
14. Seyede Sara Maroufian, K.Abbaszadeh, "Modeling and Fault Detection of an Axial Flux Permanent Magnet Motor Using Magnetic Equivalent Circuit and ARX Model",Journal of Control, Control and Instrumentation Engineers Association, Vol. 7, No. 4, winter 2013, pp. 9-18, 2013
15. Farhad Rezaee Alama, K.Abbaszadeha & Amin Saieda,"Strand Current Distribution Modeling in Turbogenerators Using Finite-element Method Based on Proposed Dual Method", Electric Power Components and Systems,Taylor & Francis Group 43(2):134-145, 2015 , DOI: 10.1080/15325008.2014.973982 , 2015
16. Housein Pardarnia, Salman Hajiaghasi, K.Abbaszadeh ,"Improved Structure of PNN Using PSA in Transformer Fault Diagnostic", Arab J Sci Eng. (39) 4845-4851 DOI: 10.1007/s 13369-014-1004-z, 2014
17. H. Paydarnia, S.Hajiaghasi, K.Abbaszadeh, "A New Approach in Online Internal Fault Detection in Distribution Transformer via PCA Neural Network", Computational Intelligence in Elec. Eng. Journal, Vol. 5 , No.2 , summer 2015
18. Ehsan Ajily, Member, IEEE, K.Abbaszadeh, and Mohammad Ardebili,"Three-Dimensional Field Reconstruction Method for Modeling Axial Flux Permanent Magnet Machines",IEEE Transactions on Energy Conversion, (Volume:30 , Issue: 1 ) Digital Object Identifier 10.1109/TEC.2014.2353299, Sep, 2014
19. A.R. Edalatian, K.Abbaszadeh, "HARMONIC MINIMIZATION IN CASCADED H-BRIDGE MULTILEVEL INVERTER BY ICA", IJTPE Journal www.iotpe.com December 2013 Issue 17 Volume 5 Number 4 Pages 72-76
20. K.Abbaszadeh, Seyedamin Saied, Siroos Hemmati, Alberto Tenconi,"Inverse transform method for magnet defect diagnosis in permanent magnet machines",IET Electric Power Applications, doi: 10.1049/iet-epa.2013.0176, 2013
21. S. Saied1, K.Abbaszadeh, A. Tenconi3 and S. Vaschetto3,"New Approach to Cogging Torque Simulation Using Numerical Functions", IEEE Transactions on Industry Applications,DOI 10.1109/TIA.2013.2293814, 2013
22. Akbar Tohidi, Ali Shamsaddinlou, Oveis Abedinia, Ali Khaki Sedigh, K.Abbaszadeh, "New Practical Design of Disturbance Rejection Control Scheme for DFIG with Wind Energy Conversion Systems",International Review of electrical Engineering (IREE) Vol 8, No 3, 2013
23. Sara Laali1, K.Abbaszadeh, Hamid Lesani,"Control of Asymmetric Cascaded Multilevel inverters Based On Charge Balance Control Methods",International Review of Electrical Engineering - April 2011 (Vol. 6 N. 2) - Papers Part A
24. K.Abbaszadeh, F. Rezaee Alam , M. Teshnehlab,"Slot opening optimization of surface mounted permanent magnet motor for cogging torque reduction",Energy Conversion and Management 55 (2012) 108-115, 2012
25. K.Abbaszadeh , F. Rezaee Alam, S.A. Saied,"Cogging torque optimization in surface-mounted permanent-magnet motors by using design of experiment", Energy Conversion and Management 52 (2011) 3075-3082, 2011
26. K.Abbaszadeh , Farhad Rezaee Alam,"Circulating current analysis between strands in armature winding of a turbo-generator using analytical model",Turk J Elec Eng & Comp Sci (2013) 21: 55 { 70c TUBI_TAK doi:10.3906/elk-1105-36, 2013
27. K.Abbaszadeh, S.Roozbehani,"A New Approach for Maximum Power Extraction from Wind Turbine Driven by Doubly Fed Induction Generator Based on Sliding Mode Control",Energy management Journal No.2 Winter 2011, pp.11-22, 2012
28. F. Tootoonchian, K.Abbaszadeh and M. Ardebili,"New Technique for Analysis of Static Eccentricity in Axial Flux Resolver", MEASUREMENT SCIENCE REVIEW, Volume 12, No. 1, 2012
29. Farid Tootonchiyan, Mohammad Ardebili, K.Abbaszadeh,"Dynamic Performance Prediction of an Axial Flux Resolver",PRZEGLAD ELEKTROTECHNICZNY (Electrical Review), ISSN 0033-2097, R. 88 NR 2, 2012
30. Tootoonchian,F., Ardebili, M., K.Abbaszadeh,"Using average DC-Pulse response of stator current for identification of axial Flux Single-Phase rotary transformer parameters",Przeglad Elektrotechniczny , 88 ( 11 A ) pp. 142 - 145, 2012
31. F.Tootoonchian, K.Abbaszadeh, M.Ardebili,"Novel axial flux brushless resolver analysis and optimization using 3D finite element and D-Q model method",Iranian Journal of Electrical & Electronic Engineering, Vol. 8, No. 3, Sep. 2012
32. S.Jamali, K.Abbaszadeh,"The Study of Magnetic Flux Shunts Effects on the Leakage Reactance of Transformers via FEM" Majlesi Journal of Electrical Engineering, Vol. 4, No. 3, September 2010, pp 47-56.
33. S.A.Saeed, K.Abbaszadeh, M.Fadaei, "Reduced Order Model of Developed Magnetic Equivalent Circuit in Electrical Machine Modeling" IEEE TRANSACTIONS ON MAGNETICS, VOL. 46, NO. 7, JULY 2010.
34. K.Abbaszadeh, M.Ardebili, E.Sarani, "Modeling and Simulation Stator Fault in induction Motor by Magnetic Equivalent Circuit" to be Accepted in Fanni Journal.
35. S.Jamali, K.Abbaszadeh, "Geometry Optimization of the Magnetic Shunt and Arrangement Influence on Axial Forces in Power Transformers Based on FEM Method"International Review on Modeling and Simulations Journal (IREMOS), ISSN 1974-9821, Vol. 2 No.5,Ocb 2009, pp 548-557
36. K.Abbaszadeh, M.Ardebili, E.Sarani, "Modeling and Diagnosis of Stator winding Fault in Squirrel Cage Induction Motor", IJES Journal ISNN 1018-7375, Vol.19 No.10 A, 2009, pp 114-121
37. S. Saied, K.Abbaszadeh,"Cogging Torque Reduction in BLDC & PMSM Motors Using Dual Structures" International Review on Modeling and Simulations, February 2009, Italy.
38. S. Saied, K.Abbaszadeh, "Cogging Torque Reduction in Brushless DC Motors Using Slot-Opening Shift", Advances in Electrical and Computer Engineering, February 2009 Vol.9 No.1,Romania
39. S.A.Gholamian, M. Ardebili K.Abbaszadeh, "Selecting and Construction of High Power Density Double-Sided Axial Flux Slotted Permanent Magnet Motors for Electric Vehicles", International Review of electrical engineering, June 2009, ISSN: 1827- 6660 Italy.
40. S.A. Saied, K.Abbaszadeh, S.Hemmati, M.Fadaee, "New Approach to Cogging Torque Reduction in Surface-Mounted Permanent-Magnet Motors" Vol.26 No.4 U.K European Journal of Scientific Research.
41. S.A.Gholamian, M. Ardebili, K.Abbaszadeh, "Effect of Air Gap on Torque Density for Non-Slotted Axial Flux TORUS and AFIR PM Motors " European Journal of Scientific Research, ISSN 0973-4562, Volume 20, Number 3, June (2008), pp:623-631
42. S.A.Gholamian, M. Ardebili, K.Abbaszadeh, S.Mahmodi Charati, "Optimum Design of 1KW Axial Flux Permanent Magnet Slotted TORUS Motor" European Journal of Scientific Research, ISSN 0973-4562, Volume 20, Number 3, June (2008), pp:623-631
43. S.A.Gholamian, M. Ardebili, K.Abbaszadeh, "Analytic and FEM Evaluation of Power Density for Various Types of Double-Sided Axial Flux Slotted PM Motors" International Journal of Applied Engineering Research, ISSN 0973-4562, Volume 3, Number 6 June (2008), pp:749-763
44. F.Bagheri, H.Khaloozaded, K.Abbaszadeh, "Stator Fault Detection in Induction Machines by Parameter Estimation Using Adaptive Kalman Filter" Iranian Journal of Electrical & Electronic Engineering, Vol. 3, Nos. 3 & 4, July 2007.
45. H.A. Toliyat, K.Abbaszadeh, M. Rahimian, and L.E. Olson, "Rail Defect Diagnosis using Wavelet Packet Decomposition" IEEE TRANSACTIONS OF INDUSTRY APPLICATIONS, VOL. 39, NO. 5, SEPTEMBER/OCTOBER 2003, pp 1454-1461.
46. K.Abbaszadeh, J. Milimonfared, M. Menhaj, H.A. Toliyat "A new approach to broken rotor bar detection in squirrel cage induction motor via model-based parameter estimation", Amir Kabir Journal of Science & Technology, has been accepted at August 20, 2002.
47. K.Abbaszadeh, J. Milimonfared, H.Vaez, " Stator Winding Fault Diagnostic in squirrel cage induction motor" Fanni Journal of science, Vol.35, No.4, Dec. 2002, pp 477-487
48. K.Abbaszadeh, J. Milimonfared, H.Vaez, "Modeling and simulation of Stator Winding in squirrel cage induction motor" Fanni Journal of science, Vol.36, No.3, Dec. 2002, pp 310-297
49. K.Abbaszadeh, E. Fallah, J. Milimonfared, et.al, "Modeling and Simulation of Dual Three-Phase Induction Machine Under Fault Conditions and Proposal of a new Vector Control Approach for Torque Oscillations Reduction", Scientia Iranica, Vol.9, No 4, pp 321-327
50. K.Abbaszadeh, J. Milimonfared, H.A. Toliyat "Broken Bar Detection in Squirrel Cage Induction Motor via Wavelet Transformation" Iranian Journal Of Science & Technology, Shiraz University, Volume 27, Number B4, 2003, pp 763-770, ISSN 0363-1307
51. J.Milimonfared, K.Abbaszadeh, M.Menhaj, H.Kazemy, " Estimation of Induction Motor Speed by E.K.F in Stationary Frame and Use of Rotor Flux and Study of Parameter Variation" Esteghlal Journal of Engineering, Isfahan University of Technology, Vol 18, No. 2 , March 2000, ISSN 1025-2851.
52. J.Milimonfared, K.Abbaszadeh, M.E.Akbari, " Design and Impelementation of PWM Rectifiers in Order to Feed & Control Motor Speed and its Abilities to Use with E.P.W.M & S.P.W.M Methods ", Amir Kabir Journal of Science & Technology, Vol.11. No. 42, fall 1999, winter 2000, ISSN.1015-0951.